螺栓轴向应力超声横纵波检测技术与实证分析
DOI:
CSTR:
作者:
作者单位:

1.北京工业大学信息科学技术学院北京100124;2.中国船级社实业有限公司北京100007

作者简介:

通讯作者:

中图分类号:

TN782;TH878;TH701

基金项目:

国家自然科学基金(52235012)项目资助


Ultrasonic longitudinal-transverse wave technique for bolt axial stress measurement and experimental validation
Author:
Affiliation:

1.School of Information Science and Technology, Beijing University of Technology, Beijing 100124,China; 2.China Classification Society Industrial Co., Ltd., Beijing 100007,China

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为提升螺栓轴向应力检测精度,基于超声纵波与横波联合分析的螺栓原位轴向应力检测方法,构建了螺栓“安装-服役”全过程的超声轴向应力检测系统。该方法通过纵波与横波联合表征,提高了长螺杆和复杂螺纹结构螺栓的轴向应力测量灵敏度和可靠性。首先,基于声弹性理论建立应力波速关系数学模型,并提出安装阶段采用单波法标定、服役阶段采用双波法的检测思路。其次,搭建超声轴向应力检测系统,对M64×450 mm高强螺栓在0~450 MPa典型服役区间内进行静态加载试验,验证方法的可行性与稳定性。最后,在海上风电场开展现场应用实验,并对在役螺栓轴力分布进行统计分析。实验结果表明,单纵波法与纵横波双波法的轴向应力测量误差分别控制在±2.55%和±1.54%以内,轴力测量误差不超过8.75 kN,系统能够在复杂工况下实现轴向应力在线检测。现场数据表明,该批螺栓轴向应力分布存在较明显离散性,轴力变异系数(coefficient of variation, CV)达到36.2%,反映出实际施工与服役条件下螺栓轴力一致性控制水平有限,验证了系统在海上风电等工程场景中的实用性与应用潜力。

    Abstract:

    To improve the accuracy of axial stress measurement in bolts, an in-situ measurement method based on the combined use of ultrasonic longitudinal and transverse waves is proposed, and an ultrasonic measurement system covering the whole process from installation to service is developed. By jointly characterizing longitudinal and transverse waves, the proposed method enhances the sensitivity and reliability of axial stress measurement for long bolts and bolts with complex threaded structures. First, a mathematical model of the stress-wave velocity relationship is established based on acoustoelastic theory, and a measurement scheme is proposed in which the single-wave method is used for calibration during installation and the dual-wave method is adopted during service. Second, an ultrasonic axial stress measurement system is constructed, and static loading tests are carried out on M64×450 mm high-strength bolts within a typical service stress range of 0~450 MPa to verify the feasibility and stability of the proposed method. Finally, field experiments are conducted in an offshore wind farm, and the axial force distribution of in-service bolts is statistically analyzed. The results show that the axial stress measurement errors of the single longitudinal-wave method and the longitudinal-transverse dual-wave method are within ±2.55% and ±1.54%, respectively, and the axial force measurement error is less than 8.75 kN, indicating that the proposed system is capable of online axial stress measurement under complex working conditions. Field results further show an evident dispersion in the axial stress distribution of the tested bolts, with the coefficient of variation of axial force reaching 36.2%. This indicates that the consistency of bolt axial force control under actual installation and service conditions is limited, and also verifies the practical applicability and engineering potential of the proposed system in offshore wind power and similar scenarios.

    参考文献
    相似文献
    引证文献
引用本文

姜涛,高杰,高翌飞,靳超,吕炎,何存富.螺栓轴向应力超声横纵波检测技术与实证分析[J].电子测量与仪器学报,2026,40(9):45-53

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-11-13
  • 出版日期:
文章二维码
×
《电子测量与仪器学报》
关于防范虚假编辑部邮件的郑重公告