基于FBG的油浸式电流互感器温度-压力复合检测研究
DOI:
CSTR:
作者:
作者单位:

1.重庆交通大学机电与车辆工程学院重庆400074;2.国网重庆市电力公司电力科学研究院重庆400000; 3.国网四川省电力公司遂宁供电公司遂宁629000

作者简介:

通讯作者:

中图分类号:

TN253

基金项目:

国家电网有限公司科技项目(2025渝电科技37#)、国网四川省电力公司科技项目(521939230001)、重庆市研究生科研创新项目(CYS25537)资助


Research on composite detection of temperature and pressure of oil-immersed current transformer based on FBG
Author:
Affiliation:

1.School of Mechatronics and Vehicle Engineering, Chongqing Jiaotong University, Chongqing 400074,China; 2.State Grid Chongqing Electric Power Co. Electric Power Research Institute, Chongqing 400000, China; 3.Suining Power Supply Company of State Grid Sichuan Electric Power Company, Suining 629000, China

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    油浸式电流互感器(current transformers, CTs)作为电网核心设备,其内部温度与压力的精准检测对保障电网安全运行至关重要。针对传统电类传感器易受电磁干扰、难以实现多参量复合检测的局限,提出基于光纤布拉格光栅(fiber Bragg grating, FBG)的油浸式电流互感器温度压力复合检测方案。首先通过理论分析,推导得出FBG中心波长随温度和压力变化的关系式,明确温度与压力对波长漂移的影响机制;然后,结合110 kV油浸式电流互感器取油阀结构特点,设计了与取油工装集成的复合传感器,通过双FBG配置实现温度与压力的解耦检测,其中FBG1结合圆形膜片结构感知压力,FBG2封装于封装杆中心通孔仅对温度敏感,利用温补光栅法消除温度交叉干扰;其次,通过有限元仿真表明,选用半径9 mm、厚度0.3 mm的铍青铜膜片时,仿真结果可满足油浸式互感器正常及故障状态下的检测需求;最后,加工传感器实物并搭建实验平台验证了传感器性能,结果表明,温度实验中FBG波长漂移量与温度线性拟合度高于0.996,温度平均灵敏度为34.96 pm/℃;压力实验中传感器压力平均灵敏度为6.475 pm/kPa,最大误差为3.819 kPa。该传感器无需改变互感器原有结构,解决了传统单一参数检测的局限性,为油浸式电流互感器的状态检测提供了可靠的新型技术手段。

    Abstract:

    Oil-immersed current transformers (CTs) are key components in power systems, and accurate detecting of their internal temperature and pressure is essential for ensuring safe grid operation. To overcome the limitations of traditional electrical sensors, such as susceptibility to electromagnetic interference and difficulty in multi-parameter detection, a temperature-pressure composite sensing scheme for oil-immersed current transformers based on fiber Bragg grating (FBG) is proposed. First, the relationship between the FBG central wavelength and variations in temperature and pressure is theoretically derived, clarifying the influence mechanism of these parameters on wavelength drift. Then, considering the structural characteristics of the oil sampling valve of a 110 kV oil-immersed current transformer, a composite sensor integrated with the oil sampling device is designed. A dual-FBG configuration is employed to achieve decoupled detection of temperature and pressure, in which FBG1 combined with a circular diaphragm structure senses pressure, while FBG2 encapsulated in the central through-hole of the packaging rod is only sensitive to temperature, and the temperature compensation grating method is used to eliminate temperature cross-sensitivity. Finite element simulation results show that a beryllium bronze diaphragm with a radius of 9 mm and a thickness of 0.3 mm can satisfy the detection requirements under both normal and fault operating conditions. Finally, a prototype sensor is fabricated and an experimental platform is established to verify its performance. Experimental results indicate that the linear fitting coefficient between wavelength drift and temperature exceeds 0.995, with an average temperature sensitivity of 34.96 pm/℃, while the average pressure sensitivity reaches 6.475 pm/kPa with a maximum error of 3.819 kPa. The proposed sensor can be installed without modifying the original structure of the current transformer, overcoming the limitation of traditional single-parameter detection and providing a reliable approach for the condition detecting of oil-immersed current transformers.

    参考文献
    相似文献
    引证文献
引用本文

孙世政,李林泽,冯澳,余欣玺,简川黔.基于FBG的油浸式电流互感器温度-压力复合检测研究[J].电子测量与仪器学报,2026,40(9):253-262

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-11-13
  • 出版日期:
文章二维码
×
《电子测量与仪器学报》
关于防范虚假编辑部邮件的郑重公告